|
1
|
| ID | NI6362 |
| Make | Anyang Forging Press Group China |
| Model | C86-75 |
| YOM | 2014 |
| Condition | Excellent ,unused |
| Photo | Photo
|
| Price | INR 1.1 Crore EXW |
Capacity : 3 tons,
Hit Energy : 75 kj,
Rated weight of falling part : 3500 kg,
Max stroke : 1250 mm,
Hit frequency per 1 min : 5s = 5 hits,
Working gas pressure : 2 - 4 mpa,
Working oil pressure : 9 - 14 mpa,
Power : 3 x 55 kw,
Min. closed dia. height (without dovtail) : 350 mm,
Distance between guides :700 mm,
Dimensions : 3700 x 1800 x 7100 mm |
|
|
2
|
| ID | NI6343 |
| Make | Wagner,German |
| Model | RAW300/40 |
| YOM | |
| Condition | excellent working condition |
| Photo | Photo
|
Video
|
| Price | INR 15 crores EXW |
1) Axial & Radial Ring Rolling Machine
Make: Wagner
Ring diameter : 300 - 3000 mm,
Ring height : 30 -400 mm,
Total weight of machine approx. : 45000 kg,
Height of rolling table above ground : 700 mm,
Max. radial rolling force : 1000 kN,
Rolling speed (standard main roll) : 1 m/s,
Standard main roll :
Nominal outside diameter : 580 mm,
Max. outside diameter (profiled) : 750 mm,
Mandrel :
Nominal outside diameter (at max. rolling force) : 190 mm,
(Smaller diameters can be used with lower forces)
Stroke of radial carriage (upper, lower mandrel carriage) : 400 mm,
Minimum center distance between main roll and mandrel : 415 mm,
Stroke of upper retaining roll : 400 mm,
Max. distance between retaining rolls : 420 mm,
Max. retaining force : 500 kN,
Drive rating, main roll drive (3-phase) : 200 kW,
Nominal torque, retaining roll drive (250 bar) : 11500 Nm,
Speed range : 0 to 150 rpm,
Drive rating, hydraulic pump motors (3-phase) total : 180 kW,
Operating voltage (3 phase) : 415 V +- 10%, 50 Hz
Operating pressure, hydraulic system : 120/265 bar,
Height adjustment referred to operating level :
Main roll : +- 10 mm,
Mandrel : +- 10 mm,
Rolling table : -10 mm,
2) Hydraulic press 1600 ton
Make : Wagner.
Capacity: 1600 ton,
Stroke length: 1100 mm,
Overall weight of machine: 92000 kg,
Overall weight of hydraulic drive station: 6500 kg,
Max. press force : 16 MN,
Mean press force: 10 MN,
Min. press force: 5 MN,
Working pressure control loop: 120 bar,
Working pressure main loop: 350 bar,
Return force: 1.75 MN,
Speed press at 5 MN: 95 mm/s,
Speed press at 10 MN: 45 mm/s,
Speed press at 16 MN: 30 mm/s,
Return travel: 280 mm/s,
Dimensions:
Max. without tool-turning device, distance between bottom edge of ram and upper edge of table: 2200 mm,
Min. without tool-turning device, distance between bottom edge of ram and upper edge of table: 1100 mm,
Clear width between columns:
From left to right: 1500 mm,
From back to front: 1000 mm,
Press ram(tool chucking area):
From left to right: 1350 mm,
From back to front: 1350 mm,
Table :
From left to right: 1350 mm,
From back to front: 1350 mm,
Above ground: 100 mm,
Height of press above ground: 7700 mm,
Rated output of main drive: 396 kW,
Subsidiary drive, approx: 35 kW,
Grease pump: Manually actuated,
Hydraulic fluid:
Type: K2K(to DIN 8659, Part 2),
Quantity approx. : 5 kg,
Cooling water:
Hydraulic system : 10.5 m3/h.
Can forge ingots to shafts too with 30% reduction in any cross section area.
3)Manipulator
Make : Toyota
Carrying capacity: 1.6 tons
Arm Length 3 meters |
|
