subscribe newsletter
Subscribe

Category : Gear Machines

Sub-Category : Gear Generator Spiral Bevel & Hypoid

Total Machines Found : 10

Select | Machine Details
 
  1
IDNA30423
MakeGLEASON PHOENIX
ModelGleason60
YOM1980
ConditionGood Condition
PhotoSee Photo
Dimensions of the workpiece :
The greatest distance between cones for gears, angle of inclination : 5 to 45 ... 30 "762 mm,
The minimum distance of the cone inside the face, around :
Pitch angle : 0 ...... 9 "228 mm,
Biggest pitch angle : 84 18 ',
The smallest angle of inclination : 5 42 ',
Extreme ratio, shafts at 90 : 10: 1
The largest diameter step gear :
at the ratio I0 : 1 .. 60 " 1524 mm,
in the ratio 2 : 1.. 531/2 " 1333 mm,
ratio 1 : 1 421/2" 1079 mm,
Maximum nominal pitch (Gleason system) : 25 Module,
The long face : 91/4 "235 mm,
Spiral angles from.. : 0 to 30
Spindle :
Diameter of conical hole of large end : 6 " 152 mm,
Cone : 3/4 " 20 mm,
Sharpening depth : 6 " 152 mm,
Front panel diameter : 54 " 1372 mm,
Feed and Speed:
Number of beats per minute : from 7 to 44
Drive :
Main drive motor : 230 V, direct current, 71/2-10 HP, 400/1600 rpm, variable speed,
Engine coolant drive : 1 HP, 1800 rpm, 220/440 volts, 60 cycles AC,
Engine lever adjustment : 3 HP, 1800 rpm, 220/440 volts, 60 AC cycles,
Lubrication drive : 3/4 HP, 1800 rpm, 220/440 volts, 60 cycles AC
Size :
Floor area, approximately : 115 "x 162" 2920 x 4100 mm,
Net weight, approx : 25.5 tons.
This machine is used to create large bevel gears and zerol bevel gears, such as used in oil well pumping and drilling equipment, steel rolling and drawing machine drives, paper equipment, coal and cement grinders, water turbines and drilling rims.
 
  2
IDNA29878
MakeSaratov Factory
Model252
YOM1965
ConditionGood Condition
PhotoSee Photo
Max. gear wheel diameter : 500 mm,
Min. gear wheel diameter : mm,
Module : 10 mm,
Max. gear wheel tooth height : 20 mm,
Inclination angle of tooth : any,
Min. length of initial cone : 0 mm,
Max. length of initial cone :
- 0 degrees 180,
- 30 degrees 260,
Inclination of inner cone : degrees 4...90
Max. width of gear crown : 65 mm,
Spiral inclination range : degrees 0...50
Number of wheel teeth : 5...100
Distance between spindle and table center : 60...360 mm,
Max. spindle movement down from the central position : 65 mm
Max. spindle movement up from the central position : 75 mm,
Size of conical opening in spindle :
- outer diameter 100,
- cone 1:20,
- cone length 150,
Spindle opening diameter : 80 mm,
Diameter of gear - cutting heads, mm 160, 200, 250, 315
Diameter of gear - cutting heads, In 6, 7, 5, 9, 12
Table movement from central position upwards and downwards : 25 mm,
Main motor power, kW 5,5
Machine dimensions : 2200 x 1600 x 1600 mm,
Machine weight : 7500 kg.
Change gears.
Cuter tools 5 pcs.
 
  3
IDNA29788
MakeGleason USA
Model102
YOM
ConditionVery good condition
PhotoSee Photo
Dia :45/4,
Up to 16 DP.
 
  4
IDNA29405
MakeRussian
Model5C270P
YOM1987
ConditionGood Condition
PhotoSee Photo
Max diameter of wheels : 500 mm,
max normal module : 8 mm,
Max height of wheel tooth : 22 mm,
Max cone distance of gear wheels : 220 mm,
Max width of gear ring : 80 mm,
Number of wheel teeth : 5-150,
Min angle of dividing cone : 5,
Stock angle : max:+90, min:+5,
Distance of end face from the spindle to the center : max (when stock adjustment angle is 5 degree) : 450 mm, - min (when stock adjusting angle is 90 degree) : 75 mm,
Min hypoid displacement : upper-80 mm, down-80mm,
Weight of the machine : 6 ton.
 
  5
IDNA29404
MakeRussian
ModelCT270
YOM1984
ConditionGood Condition
PhotoSee Photo
Max. gear wheel diameter : 500 mm,
Module : 8 mm,
Max. gear wheel tooth height : 22 mm,
Max. gear wheels cone distance : 220 mm,
Max. gear ring width : 80 mm,
Inclination angle of tooth : any,
Number of wheel teeth : 5...150,
Min. angle of dividing cone : 5 degrees,
Table diversion to edge : 100 mm,
Nominal diameter of gear - cutting heads : 100, 125, 160, 200, 250, 320, 400 mm,
Machine dimensions : 2885 x 2570 x 1995 mm,
Machine weight : 9000 kg.
For finishing bevel and hypoid gears with circular teeth.
 
  6
IDNA29403
MakeRussian
ModelCT280.022
YOM1991
ConditionGood Condition
PhotoSee Photo
Work piece maximum diameter : 800 mm,
The greatest external district module : 16 mm,
The greatest external height of a spur : 36 mm,
The greatest average conical distance : 360 mm,
The greatest width of a gear wreath : 125 mm,
The least corner of a dividing cone : 5 degree,
Number of spur : 5-150,
The greatest hypoid displacement :- up : 125 mm, down : 125 mm,
Distance from an end face of a spindle of a wheel head of a product up to the center of a semiautomatic device : 135-600 mm,
Nominal diameter of spur-carved heads : 160; 200; 250; 315; 400; 500 mm,
The greatest radial installation of a tool spindle concerning an axis : 320 mm,
Frequency of rotation of a tool spindle : 18-172 rpm,
Time of a cycle с 7 And more,
Main electric motor power : 7,5 kW,
Total power of the installed electric motors : 17 kW,
Machine overall dimensions :-
Length : 3485 mm,
Width : 3730 mm,
Height : 2860 mm,
Machine weight : 16,395 kg.
 
  7
IDNA28750
MakeModul
ModelZFTKK500/2W
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
Max wheel diameter : 540 mm,
Max gear width : 78 mm,
Module : max 16, min 1,
Description Number of teeth : 6-100,
Min/max pitch cone length : 270 mm,
Min/max. pitch cone angle : 90 ,
Milling spindle turning speed range : 23 - 224 U/min,
Blade cutter head diameter : 6 - 300 mm.
 
  8
IDNA28737
MakeGleason USA
Model106
YOM
ConditionGood Condition
PhotoSee Photo
Max.cone distance: 107 mm,
Max. pitch diameter (30 spiral angal) :
10 to 1 ratio : 215 mm,
2 to 1 ratio : 190 : mm,
1 to 1 ratio : 152 mm,
Max. face width: 31.7 mm,
Max depth : 15.8 mm,
Diametral pitch, coarsest : 6.35 Mod. ,
WORK SPINDLE
Diameter of taper hole at large end: 23 mm
Taper per foot : 15.5 mm,
Depth of taper: 152.4 mm,
Diameter of hole through spindle: 61.9 mm
Work Head Settings
Offset above center, maximum :76.2 mm,
Offset below center, maximum : 76.2 mm,
Distance from machine center to nose of spindle (maximum) : 31.7 mm,
ELECTRICAL EQUIPMENT
Main motor: 1500 RPM
Hydraulic motor : 1500 RPM
Coolant pump: 1 horsepower, 3600 rpm (3000 rpm for 50 cycle),
Miscellaneous
Floor space : 2133 X 1549 mm,
Height : 1676 mm,
Net weight : 1676 mm,
Size of case : 1981 mm,
 
  9
IDNA28734
MakeGleason USA
ModelNo 2
YOM
ConditionVery good condition
PhotoSee Photo
Dia :41/4,
Up to 16 DP,
Max face width 7/16,
Quantity No. : 3.
 
  10
IDNA27143
MakeGleason USA
Model463
YOM
ConditionGood Condition
PhotoSee Photo
Max pitch diameter : 863 mm,
Max face width: 76 mm,
Cone distance (max. 30˚ spiral angle and 12" diameter wheel) - 15"/(381mm)
Maximum pitch angle, shafts at 90˚ - 71˚ 34'
Minimum pitch angle, shafts at 90˚ - 5˚ 42'
Extreme ratio, shafts at 90˚ - 3 to 1
Maximum pitch diameter: (90˚ shafts):
Spiral angle 0˚, ratio 1 to 1 - 15.5"/(393.7mm)
Spiral angle 0˚, ratio 3:1 - 23"/(584.2mm)
Spiral angle 30 ˚, ratio 1:1 - 21"/(533.4mm)
Spiral angle 30˚, ratio 3:1 - 31.5"/(800.1mm)
Spiral angle 45˚, ratio 1:1 - 22.5"/(571.5mm)
Spiral angle 45˚, ratio 3:1 - 34"/(863.6mm)
Coarsest diametral pitch / metric module 2 DP / 12.7
Maximum face width 3"/(76.2mm)
with full set of dressers, hydraulic chucking, guards, coolant.
top