subscribe newsletter
Subscribe

Category : Forging Equipment

Sub-Category : Part Former Hot

Total Machines Found : 13

Select | Machine Details
 
  1
IDNA30885
MakeSakamura
ModelHBP100
YOM
ConditionGood Condition
PhotoSee Photo
4 die hot bearing former,
Forge tonnage rating : 230 tons,
Max part OD : 64 mm,
Min-Max blank height : 12 - 30 mm,
Bar Diameter : 25 - 40 mm,
Cutting length : 20 - 70 mm,
Forming Stations : 4,
Production rate : Up to 90 per minute,
Die inter-center crank pin dia : 240 mm,
Crank pin diameter : 360 mm,
Ram stroke : 80 mm,
Ram Stroke : 240 mm,
Ejector stroke : 40 mm,
PKO : 20 mm,
Main motor power : 75 Kw,
Machine weight :60 tons.
Inner and outer bearing races can be forged and separated simultaneously from bar stock in full automatic operation.
Complex forgings such as gear blanks can also be forged.
 
  2
IDNA30694
MakeSakamura
ModelPF550
YOM1970
ConditionGood working condition
PhotoSee Photo  |  See Video
Station : 5 Stations,
Capacity : 550 ton,
Cutting Diameter : Max 23 mm,
Cutting Length : Min 10 mm Max 48 mm,
Output per minute : 57 pcs,
Crank Stroke : 280 mm,
Die Diameter : 125 mm,
Quill Diameter : 80 mm,
Die Pitch : 150 mm,
K.O. Stroke : 69 mm,
P.K.O Stroke : 15~45 mm.
 
  3
IDNA30378
MakeHatebur
ModelAMP20
YOM1976
ConditionVery good condition
PhotoSee Photo
Number of forming dies : 3,
Production : 130-190 ppm,
Max. outer diameter for round parts : 35 mm,
Max. width across flats (hex) : 33.3 mm,
Bar diameter : 14-28 mm,
Cutoff Length : 15-40 mm,
Forging Tonnage : 900 kN,
Drive motor rating : 22 kw,
Center distance of dies : 110 mm,
Die diameters:
1st and 3rd stations : 80 mm,
2nd Station : 100 mm,
Main ram stroke : 110 mm,
Ejector Stroke : 55 mm,
Dimensions and weights:
Length : 3200 mm,
Width : 2600 mm,
Height :1550 mm,
Weight (w/Motor).. 11.0 tons,
Electrics:
Main drive : 22 KW,
Power supply : 380 volt 3 phase 50 cycles,
Equipped with:
- Variable Speed Drive
- Split second safety stop
- Overarm-type main slide
- Late model Induction Heater
- Extensive amount of drawings, manuals, etc.
- One-piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized lubrication system
- Bar Rack and Workers Platform
-Automatic bar feeder
-Cefi 150kw, Induction heater, built 1999
-Auto Water recycling system
-Spare parts & tooling
-Manuals & Drawings
-Upgraded Electronics
 
  4
IDNA30370
MakeTyazhpressmash
ModelTPM30
YOMRetrofitted 2019
ConditionGood working condition
PhotoSee Photo  |  See Video
Capacity : 250 tons,
Capacity: 2500 kN,
Slide stroke: 160 mm,
Slug length for one forged part:
Minimum: 20 mm,
Maximum: 72 mm,
Max. forged part OD: 67 mm,
Max. forged part height: 40 mm,
Slide SPM: 10...120 min-1,
Die kick out stroke: 70 mm,
Punch kick out stroke: 26*1 mm,
Number of stations:3,
Distance between forming stations: 160 mm,
Distance between cut of station and the 1 st forming station: 16 mm,
Slug weight: 0,05...0,7 kg,
Total power of electric motors: 72,02 kW,
Main drive electric motor power: 71 kW,
Compressed air pressure: 0,4+0.1 MPa,
Cooling water pressure : 0,6 MPa,
Hot former overall dimensions:
Length: 5330 mm,
Width: 3230 mm,
Height above floor level: 2980 mm.
 
  5
IDNA30369
MakeHatebur
ModelAMP50
YOMRetrofitted 2019
ConditionGood working condition
PhotoSee Photo  |  See Video
Dia : 50 mm,
Capacity : 800 tons
Type : 4-Die Hot Former,
Part Dia : 92 mm,
Max Cutoff Length : 110 mm,
Max Die Ejector : 90 mm,
Part Wt : 2 kgs,
Min Cutoff Length : 32 mm,
Max Outer Dia for Combination Parts : 82 mm,
Max Width Across the Flats Hex : 80 mm,
Max Strokes per Minute : 90,
Die Diameter 1st : 160 mm,
Die Diameter 2nd : 200 mm,
Die Diameter 3rd : 200 mm,
Die Diameter 4th : 200 mm,
Ram Stroke : 240 mm,
Punch Ejector Stroke : 35 mm,
Machine Length : 7,500 mm,
Machine Width : 5,220 mm,
Machine Height : 2,650 mm,
Machine Weight : 81.8 tons.
 
  6
IDNA29560
MakeMinster
ModelE2400
YOM1981
ConditionGood working condition
PhotoSee Photo
Forming sections : 7,
Area of slide : 2438 x 1066 mm,
Press power : 400 tons,
Area of bolster : 2438 x 1066,
Stroke of side : 203.2 mm,
Adjustment : 152.40 mm,
Distance floor to top of bed : 914.4 mm,
Shut height on bed : 914.4,
Shut height on bolster : 762 mm,
Stroke per minute : 35-70,
Thickness of sheet : 0.8-3 mm,
Width of sheet : 50-200 mm,
Diameter range : 90-190 mm,
Quantity no : 2
Material used for cages production :TDA (double pickeld sheet),
Overall dimensions (W x L x H ) : 3400 x 5400 x 6000 mm,
Weight : 63.5 tons.
Technical Documentation is Available.
Automatic transfer press, with 7 forming sections, it makes bearing cages from metal sheet band for radial ball bearings and axial deep groove tapered roller bearings.
In our factory had been producing tapered roller bearings cages with diameter of 114 mm.
 
  7
IDNA29024
MakeTyazhpressmash
ModelAO341
YOM1985
ConditionGood working condition
PhotoSee Photo  |  See Video
4-Die Hot Former
Capacity : 1250 tons,
Max outer diameter : 120 mm,
Max outer diameter for combination blanks : 110 mm,
Max width across flats (hex) : 105 mm,
Max part height : 80 mm,
Bar diameter range:
max : 60, mm,
min : 36 mm,
Cutoff length range:
max : 135 mm,
min : 45 mm,
Blank weight range :
max : 3 kgs,
min : 0.4 kgs,
Drive motor rating : 315 kw,
Machine dimensions with motor:
Length : 9200 mm
Width : 5900 mm,
Height without hoist : 3100 mm,
Height with hoist : 4900 mm,
Weight of machine with motor :170 tons.
 
  8
IDNA27035
MakeTyazhpressmash
ModelTPM50XL
YOMBrand New
ConditionBrand New
PhotoSee Photo  |  See Video
Capacity:8000 ton,
Max. OD of a single ring: 104 mm,
Max. OD of a double ring: 94 mm,
Maximum height of a single product: 60 mm,
Initial slug diameter
Maximum: 50 mm,
Minimum: 28 mm,
Initial slug length:
Maximum,: 110 mm,
Minimum: 25 mm,
Initial slug weight: 0,17-1,7 kg,
Slide strokes per minute (step less adjustable)
Maximum: 100 spm,
Minimum: 60 spm,
Slide stroke: 240 mm,
Die kick out stroke: 90 mm,
Punch kick out stroke: 48 mm,
working stations number: 4 no,
Distance between forming stations: 240 mm,
Distance between cut off station and the 1st forming station: 210 mm,
Feed C.1. height above floor level: 1500 mm,
Number of short ends per bar discharged at automatic max: 3 no,
Main drive electric motor power: 235 kWt,
Power supply mains requirements: 3-phase
380V10%
50Hz
Power supply requirements for control system: 220
24 V,
Compressed air pressure: 0,6 MPa,
Cooling water pressure: 0,5-0,6 MPa,
Cooling water consumption: 70 m3/hour
Hot former overall dimensions
Length: 9770 mm,
Width:7140 mm,
Height (above floor level): 5000 mm.
 
  9
IDNA27034
MakeTyazhpressmash
ModelTPM30
YOMBrand New
ConditionBrand New
PhotoSee Photo  |  See Video
Capacity: 2500 kN,
Slide stroke: 160 mm,
Slug length for one forged part:
Minimum: 20 mm,
Maximum: 72 mm,
Max. forged part OD: 67 mm,
Max. forged part height: 40 mm,
Slide SPM: 10...120 min-1,
Die kick out stroke: 70 mm,
Punch kick out stroke: 26*1 mm,
Number of stations:3,
Distance between forming stations: 160 mm,
Distance between cut of station and the 1 st forming station: 16 mm,
Slug weight: 0,05...0,7 kg,
Total power of electric motors: 72,02 kW,
Main drive electric motor power: 71 kW,
Compressed air pressure: 0,4+0.1 MPa,
Cooling water pressure : 0,6 MPa,
Hot former overall dimensions:
Length: 5330 mm,
Width: 3230 mm,
Height above floor level: 2980 mm.
 
  10
IDNA24439
MakeHatebur
ModelAMP20
YOM1991
ConditionGood working condition
PhotoSee Photo
Press Capacity : 220 tons,
Forming section : 3,
Forming load: 90 ToF,
Bar Diameter: 14 to 25 mm,
Part Outer Diameter, Max.: 35 mm,
Cut-Off Length: 15 to 40 mm,
Ram Stroke: 110 mm,
Ejector Stroke: 55 mm,
Die Center Distance: 110 mm,
Production Per Minute: 12 to 180 ,
Weight: 11 tons,
Technical documentation : yes.
With AMP 20 it used to be made directly from heated bar through induction, nuts from M12 until M22 and bar diameter between 14 25 mm.
 
  11
IDNA24438
MakeHatebur
ModelAMP30
YOM1991
ConditionGood Condition
PhotoSee Photo
Press Capacity : 230 tons,
Forming section : 3
Max outer diameter of piece : 64 mm,
Max OD for Combi blanks : 55 mm,
Main ram stroke : 160 mm,
Power of induction heating installation : 800 kW,
Electric start power : 100 KVA,
Bar diameter : 19-40 mm,
Cutting width : 22-72 mm,
Weight of pieces : 50-700 gr,
Stroke : 70-120 min,
Main motor : 56 kW,
Weight of the machine : 35.8 tons,
Tools: yes,
Technical documentation : yes,
Spare parts : 1 electric engine.
 
  12
IDNA24437
MakeNational,USA
ModelHF6/4
YOM1980 Recond 2004
ConditionGood working condition
PhotoSee Photo
Forming sections: 4, Press capacity: 1200 ToF , Max outer diameter of piece 120 mm , Max. bar diameter: 65 mm, Length for cutting: 45-140 mm , Stroke of ram: 381 mm, Stroke of cutting arm: 254 mm, Stroke: 40-70 /min, Weihht of piece: 0.4-3.1 kg, Power of induction heating installation 3.000 KW, Main motor power 300 KW, Power of auxiliary motors 7.1 KW, Productivity: 1650-4500 pcs/h, Weight: 180 tons.
This machine has induction system also included
Type : T.T.U. Al,
Manufacturer : electroputere,
Rated capacity : 4000 / 2000 / 2000 KVA,
High - voltage : 600 V,
Low - voltage : 5700 V,
Output - voltage : 546 V,
Frequency : 50 Hz,
Phase : 6,
Connection method : Dyn11.
In 2004 the National HF 6/4 machine was completely reconditioned, besides replacing the mechanical components used, it was made the complete replacement of the induction heating installation
with a new one; also the original lubrication system TRABON was updated. In the URB bearings plant with this National 6/4 it used toproduce bearing rings, maximum outer diameter 120 mm, for oscillating bearings with balls, radial bearings and tapered rollers bearings, from bar steel 100 Cr6 (Max. diameter of bar is 65 mm), with the maximum weight of 3.1 Kg. Also, on this machine it had been made cardan crosses.
Electric engine : 1 piece,
Adjustment wedges : 2 pieces,
Superior pliers : 1 piece,
Inferior pliers : 1 piece,
Die mass clamping piston : 1 piece,
Break belt :1 piece.
 
  13
IDNA24434
MakeHatebur
ModelAMP70
YOM1965 Rebuilt 2002
ConditionDisassembled
PhotoSee Photo
Forging tonnage capacity : 1200 tons,
Forming stations : 4 no,
Max outer part dia : 145 mm,
Max outer dia combo blanks : 122 mm,
Bar dia range : 36 - 75 mm,
Initial weight : 0.4-5.0 kg,
Cutoff length range : 45 - 135 mm,
Max across the flats : 105 mm,
Die center distance : 320 mm,
Die dia 1st/2nd, 3rd & 4th : 200 / 270 mm,
Stroke rate : 50-80 per min,
Machine weight : 175 tons.
Technical documentation and the drawings are available.
top